Filter By:
- Parts & Accessories (23)
- Wheels (1)
- Hubs (2)
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
- Show More Model Years
- Show Fewer Model Years
Wheels
$1.80 - $7.35
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels.
- 14mm x 1mm (1411-AN) sold in pairs
- All others sold individually
$11.50 - $48.00
We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims.
- Teravail Tubeless Tape comes in a variety of widths to fit almost any rim.
- Teravail Tubeless Tape is available in a variety of widths and roll lengths.
- Ten-meter length is enough for a single layer on approximately four wheels
$25.00 - $29.99
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
$122.50
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed.
- 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration
- Chromed steel bearings
- Wide bearing stance and axle design reduces flex and adds durability
- Low drag main seal prevents contamination and reduces resistance
- Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components
$20.00 - $21.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate
- SealLock end caps feature a low friction U-cup seal that snaps into place
$20.00 - $23.00
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs
- SealLock end caps feature a low friction U-cup seal that snaps into place
$3.99
Stan's No Tubes' Presta Removable Valve Core is a replacement valve core for Stan's No Tubes Presta valve stems and Presta valve equipped rim strips.
$18.99 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims.
21mm width fits:
- ZTR Olympic
- ZTR Iron Cross
- ZTR 355
- ZTR Alpine
- ZTR Crest
- ZTR Alpha 340 (2 layers)
- ZTR Alpha 400 (2 layers)
- Most road clincher rims
25mm width fits:
- ZTR 355 (26", 650b, 29")
- ZTR Crest
- Crest MK3
- ZTR Arch EX
- ZTR Flow EX
- Crest S1
27mm width fits:
- ZTR Flow EX
- ZTR Bravo
- ZTR Hugo 52mm
- Arch S1
- ZTR Rapid 28
- ZTR Rapid 30
- Arch MK3
30mm width fits:
- ZTR Flow MK3
$25.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant.
Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads:
- MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi
- ERD 615, 622x49.9, 29 in x 52.3mm
Your rim has a stepped valve and is not compatible with this Schrader valve.
$4.98
Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!
$42.00
SRAM's Quick Releases hold your wheel tightly in place, are built for ease of use and made to last, too. You get a front and rear quick release.
$42.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option.
Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes.
- Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles.
- Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design.
- Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength.
- Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal.
- Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
- The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry.
- No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench.
- Designed, built, and quality tested in the USA. Proven around the world.
$54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season.
- When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out.
- The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability.
- No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench.
- Designed, built, and quality tested in the USA. Proven around the world.
Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$57.97
The best price on the market for a wheel meant to be ridden. Single-wall rims and loose-ball hubs that come out of the box round and true.
$19.99 - $24.99
Booster thru-axle hub spacer kits are designed to give your non-Boost front and rear thru-axle hubs the boost they need to fit any Boost-compatible frame or fork.
$25.00
These lightweight valves help prevent clogging from tubeless sealant.
- Aluminum
- 40mm length
$44.99
Hope Front Axle Conversion Kits
· Compatible with Pro 2 and Pro 2 Evo hubs
· Converts all Hope Pro 2 and Pro 2 Evo hubs to 15mm through axle hubs
$39.52
Hope Front Axle Conversion Kits
· Compatible with Pro 2 and Pro 2 Evo hubs
· Converts all Hope Pro 2 and Pro 2 Evo front hubs to 20mm through axle hubs
$6.18 - $11.98
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity
- No retainer means these bearings have 40 percent more capacity
$44.00
The mounting solution for thru-bolt front wheels.
Designed for an axle diameter of 9mm in the front, the thru-bolt system is a special kind of axle mounting for bikes. The DT Swiss thru-bolt system is compatible with standard quick-release dropouts but requires hubs that are compatible with the Thru Bolt. The stronger wheel connection results in greater stiffness.
- Overall Length: 115mm
- Thread Pitch: M9 x 1.0mm
- Flat Washer
$50.00
The mounting solution for Thru Bolt rear wheels.
Designed for an axle diameter of 10mm in the rear, the thru bolt system is a special kind of axle mounting for bikes. The DT Swiss thru bolt system is compatible with standard quick-release dropouts, but requires matching hubs. The stronger wheel connection results in greater stiffness.
- Overall Length: 152mm
- Thread Pitch: M10 x 1.0mm
- Flat Washer
$81.80 - $99.60
Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs.
- End Cap Included
$13.40
This outer receiver unit works with the CJ-S700 Cassette Joint Unit for Shimano Alfine SG-S700 internally geared hub. This part can become worn, cracked, or torn, exposing the shift cable and possibly other components to unwanted dirt, water, mud, you name it. You don't want that.
Page 1 of 1